Audio-damage Phosphor Instrukcja Użytkownika Strona 15
- Strona / 21
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
The sliders are bidirectional. If left at their center position, no signals from the LFOs reach the corresponding
parameter in the oscillators and filters. In general, moving a slider to the right of center causes the LFO to
increase the parameter’s value and moving it to the left of center causes the LFO to decrease the parameter’s
value. Simply click and drag on a slider to change its value. If you hold down the CTRL key on your keyboard
and click the slider, the slider will return to its center position.
More specifically, the sliders under the headings “LFO to Primary Osc” and “LFO to Secondary Osc” have the
following functions:
PITCH – moving the PITCH slider to the right causes the LFO to raise
the pitch of the oscillator, moving it to the left causes it to lower the
pitch. Use the PITCH slider to introduce subtle vibrato and trill effects,
or not-so-subtle pitch slides and jumps.
PAN – moving the PAN slider left or right of center causes the LFO to
move the output of the oscillator in the corresponding direction in the
stereo field. Note that the LFO’s influence is added to the position set
by the PAN slider in the Oscillator panes. Hence if for instance the
Oscillator PAN slider is set to the far left, and you move the PAN
modulation slider to the left, you won’t hear any change in the
oscillator’s position because the LFO can’t push it any further to the
left.
AMP – moving the AMP slider to the right of center causes the LFO to make the Oscillator louder, moving it to
the left causes the LFO to make the Oscillator quieter. The effect of the LFO is added to the loudness of the
oscillator as set by the LEVEL slider in the Oscillator pane.
NOISE - moving the NOISE slider to the right of center causes the LFO to make the noise generator louder,
moving it to the left causes the LFO to make the Oscillator noise generator. The effect of the LFO is added to
the loudness of the noise generator as set by the NOISE slider in the Oscillator pane.
The sliders under the heading “LFO to Filter” connect the LFOs to the
filters following the delay lines. The LFOs can modulate (change) the
frequencies of the filters. Moving these sliders to the left of center causes
the LFOs to decrease the filter frequencies (as if you were dragging the
dot in the filter’s control to the left), and moving the sliders to the right causes the LFOs to increase the filter
frequencies.
- Phosphor User’s Guide 1
- Audio Damage, Inc 1
- Release 1.1 1
- Introduction 5
- System Requirements 6
- Installation 6
- Operation 7
- 2. Envelope Generators 9
- Crossmod 10
- Velocity Amount (Amt) 11
- Pitch Offset 11
- 5. Modulation Sliders 14
- CTRL key on your keyboard 15
- 6. Delay and Filter Controls 16
- L+R Link 18
- Rand All 18
- Poly Mode 19
- Portamento 19
- Delay Mix 19
- Output 19
- MIDI Controllers 20
- Automation 21
- Presets 21
- And Finally… 21
Powiązane produkty i podręczniki dla Instrumenty muzyczne Audio-damage Phosphor
(22 strony)Parkinson Cowan L50GS1WN manuály
Uživatelské manuály a uživatelské příručky pro Pomalé vařiče Parkinson Cowan L50GS1WN.
Poskytujeme 1 manuály pdf Parkinson Cowan L50GS1WN ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentarze do niniejszej Instrukcji